QU20289U Used Right Steering Knuckle for 1986-1994 Ford F250 Dana 50

QU20289U Used Right 1986-1994 Ford F250 Dana 50 Steering Knuckle includes spindle studs, fits the passenger side axle beam on 1986 to 1994 Ford F250 4x4 trucks with Dana 50IFS front axles. Available while supplies last.

Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!

Dan the Gear Man® Tech Notes:
GVW F250s
Caliper Type
Ball Joints
Camber Bushings
Pivot Bushing
Matching Parts and Tools
Applications

Tech Note 1: GVW F250s
F-250 4x4s were available with either the 3800/3850 pound capacity Dana 44IFS or the optional 4600 pound rated Dana 50IFS Independent Front Suspension Twin Traction Beam® front drive axles. QU20289U Steering Knuckle only fits the heavy GVW F250s with Dana 50IFS front axles. If you are not sure which axle your F250 has, look at the front hubs. Dana 44 front hubs have an outside diameter roughly 3-3/8". Dana 50IFS axle hub diameter is about 4-1/8".

Tech Note 2: Caliper type
Ford used several different steering knuckle part numbers for the 1980-1997 era Dana 50IFS front axle. There are three major knuckle variations depending upon the type of brake caliper used. From 1980 to 1985 the calipers are held in place by a slide and spring placed between the lower edge of the caliper and the knuckle casting. 1986-1994 calipers are retained by upper and lower long, diamond shaped rubber and steel pins. Each end of the caliper has a V-shaped groove as does the caliper support arms that are part of the knuckle. 1995-1997 knuckles are made for bolt-on caliper anchor plates. There are also casting differences for the first two knuckle types depending upon the year.

Tech Note 3: Ball Joints
This Steering Knuckle does not include Ball Joints. Order QK4561 Complete Ball Joint Set or QA50095 Upper and QU50056 Lower Individual Ball Joints.

Tech Note 4: Camber Bushings
The axle beams were the same for 1986-1994 axles, but different replaceable upper ball joint camber bushings were used depending upon the year and suspension. In many, perhaps most cases, the original camber bushing was replaced during a front end alignment at some point in the vehicles history. If possible, reuse the camber bushing from your old ball joints, then have your front end aligned by a competent front end specialist who can check and change toe-in, camber, and caster as needed.

Tech Note 5: Pivot Bushing
Due to the age of the vehicles this knuckle fits, I recommend you replace the Axle Beam Pivot Bushing with a new QU50097 Axle Beam Pivot Bushing at the same time you replace the knuckle and ball joints.

Tech Note 6: Matching Parts and Tools
QK4561 Ball Joint Set (2 Uppers and 2 Lowers)
QA50095 Upper Ball Joint
QU50056 Lower Ball Joint
QU20065 Brake Caliper Pin
QU20280U Used Left Axle Beam
QU20281U Used Right Axle Beam
TK20227 Dana 50 Spindle
QU95036 Locknut for Spindle Studs
QU20288U Left Steering Knuckle
QU50097 Axle Beam Pivot Bushing
QU40087 Dana OE Left Axle Shaft Seal (1980-1997)
QU40088 Dana OE Right Axle Shaft Seal (1983-1997)
TS4511 Ball Joint Press Set
S24200 Medium Strength Threadlocker
S82194 Ultra Gray RTV Sealant

Applications:
Ford:
F-250 with the Dana 50IFS Front Axle: 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994