QU50285U USED 27 Spline NP205 Input Shaft

QU50285U USED 27 Spline NP205 Input Shaft for all Chevy and GMC trucks with New Process NP205 Transfer Cases and Turbo 350 or early Turbo 400 Automatic Transmissions. Note: this is a good useable part, but there will be some visable wear on the clutch teeth. Available while supplies last.

Also See QU50285 New 27 Spline NP205 Input Shaft

Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!

Dan the Gear Man® Tech Notes:
1973-earlier Turbo 400 Transmissions
Worn Clutch Teeth
Inspect for Wear
Matching Parts
Tech Help
Applications

Tech Note 1: 1973-earlier Turbo 400 Transmissions
Most if not all early Turbo 400 transmissions (prior to 1973) have 27 spline output shafts. Later models use 32 spline shafts.

Tech Note 2: Worn Clutch Teeth
The most common wear issue with NP205 input shafts is worn clutch teeth. It does not take much wear on the input shaft and sliding clutch collar teeth for the transfer case to "jump" out of high range. If your input shaft has significant wear on the clutch teeth, replace it and the sliding collar.

Tech Note 3: Inspect for Wear
NP205 Input Shafts may also have damaging wear on other locations. Input shaft with significant wear that can be felt with your fingernail should be replaced with a new shaft along with the matching component. Look for wear at these locations:
Rear Bearing Pilot: Indentations from the needle rollers that fit in the front of the rear output shaft
Helical Gear Teeth: If run short of oil, teeth will show temperature discoloration and/or visible wear
Input Splines: Visible wear on the splines is usually caused by lack of lubrication

Tech Note 4: Matching Parts
Matching Parts for QU50285U Input Shaft:
TK50119 Input Ball Bearing
QK2175 Series Selective Fit Input Shaft Snap Rings
QU50275 Set of 15 Needle Roller Bearings for Input Shaft to Rear Output Shaft Connection
QU30001 27 Spline Transmission to Transfer Case Splined Coupler
QU30075 Input Shaft to Splined Coupler O-Ring
TK30046 Transmission to Adapter O-Ring
TK10516 8 Bolt Figure-8 Adapter to Transfer Case Gasket
QU50167 Input Seal (requires 2 for most applications)
TK10661U/QU50339 Sliding Clutch Collar Ring
TK50084 Rear Output Shaft
QA2061 Complete Small Parts Kit
TK2000MOH Series GM NP205 Master Overhaul Kits
TK2000GS Series GM NP205 Gasket and Seal Kits

Tech Note 5: Tech Help
Need Tech Help on rebuilding your NP205? Get my TM2000 New Process NP205 Transfer Case Service Manual. A Complete NP205 shop Manual with over 375 color photographs is your indispensable NP205 resource for Repair Procedures and Parts Identification. Complete coverage of Disassembly, Inspection, and Reassembly Procedures. Also, Shop Notes, Tool Recommendations, Complete Parts Guide, and full color Exploded Views, including Right Drop and Left Drop Models, plus GM Specific Parts. Covers New Process NP205 Transfer Cases found in Chevrolet, Dodge, Ford, GMC, and International Harvester (IHC) 4x4 vehicles from 1969-1993.
Or my TM2002 for the Exploded Views and Parts Guide only. Fully Illustrated with dozens of crisp color photographs for EASY Parts Identification! This Manual includes 10 page Parts Identification Guide with full color Exploded Views.

Applications:
Chevy and GMC:
K5 Blazer, K5 Jimmy, K10, K15, K1500, K20, K25, K2500 with Automatic Transmissions and NP205: 1969, 1970, 1971, 1972
K5 Blazer, K5 Jimmy, K10, K15, K1500, K20, K25, K2500, K30, K35, K3500 with Turbo 350 Automatic & NP205: 1973, 1974, 1975, 1976, 1977, 1978
K5 Blazer, K5 Jimmy, K10, K15, K1500, K20, K25, K2500 with Turbo 350 Automatic & NP205: 1979, 1980