QU40572U Used Axle Shaft Slip Yoke Boot for Ford IFS Front Axles

QU40572U Used Axle Shaft Slip Yoke Boot for Ford Twin Traction Beam® Front Axles is a genuine original equipment part for 1990-1997.5 Dana 35IFS Ranger, Bronco II, and Explorers, and all 1984-1996 Ford Dana 44IFS and 1983.5-1997 Ford Dana 50 IFS Twin Traction Beam® front axles in full size Ford 4x4s. Sold individually. Available while supplies last.

Order QU40084 and QU40085 clamps separately.

New Boot QU40572 Axle Shaft Slip Yoke Boot.

Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!

Dan the Gear Man® Tech Notes:
Eliminating Axle Shaft Spline Failure
Replace Worn Boot
Replace Boot Clamps
Pre-Grease
Installation Tip
Matching Parts
Applications

Tech Note 1: Eliminating Axle Shaft Spline Failure
Ford introduced a redesigned Dana 44IFS Twin Traction Beam Front Axle during the 1983 model year that uses a right Axle Slip Joint protected by a flexible rubber Boot instead of a pressed on Yoke Seal. The Slip Yoke Boot eliminated one of the chronic problems the previous 1980-early 1983 axle had, namely axle shaft spline failure from water and grit infiltrating past the seal.

Tech Note 2: Replace Worn Boot
Replace any Slip Yoke Boot that is damaged or torn. A damaged Boot will allow water and crud in which will destroy your axle shaft splines. Axle shafts are expensive!

Tech Note 3: Replace Boot Clamps
Always replace the Boot Clamps anytime they are removed. QU40084 (Slip Yoke side) and QU40085 (Axle Shaft side) Boot Clamps will provide a 360 leak-proof seal between the Boot and Yoke or Shaft. Makeshift methods like Tie Straps and Twisted Wire cannot seal a boot 100%! Rusted, worn out axle shaft splines will cost you BIG Dollars!

Tech Note 4: Pre-Grease
Always pregrease the axle shaft and slip yoke splines before assembly with QU90018 or similar NLGI #2 GC-LB water resistant grease.

Tech Note 5: Installation Tip
When starting the axle shaft splines into your new Slip Yoke, verify that the Slip Yoke and Right Axle Shaft are as close to being in phase as possible. (The center line of the yoke holes line up to each other with little or no offset.)

Tech Note 6: Matching Parts
Interactive Exploded View XV1010DT 1995, 1996, 1997 Ford F250 Dana 50IFS Axle
TK40712 and QU90007 Universal Joints for Dana 44IFS
TK40719 and QA4874 Universal Joints for Dana 50IFS
QU40084 Slip Joint Boot Clamp for Large End (Slip Yoke)
QU40085 Slip Joint Boot Clamp for Small End (Axle Shaft)
QU40557 Inner Slip Yoke Seal
QU40626 Dana 44IFS Axle Slip Yoke for 1983-1996 Bronco, F150, and standard axle F250
QU40815 Dana 50IFS Axle Slip Yoke for 1983-1997 F250, 1983-1985.5 F350
QU40087 Left Axle Shaft Seal
QU40088 Right Axle Shaft Seal 1983-1997
QU40534 Right Differential Output Bearing and Seal Kit
QU40616 Dana 44IFS Right Axle Shaft for F250 (3800 or 3850 pound rated axles)
QU40263 Dana 44IFS Right Axle Shaft for Bronco and F150
QA4774 Dana 50IFS Right Axle Shaft Assembly (includes inner and outer shafts plus u-joint)
QU40435 Dana 50IFS Right Inner Axle Shaft for 1980-1997 F250, 1980-1985.5 F350
QU95036 Spindle to Steering Knuckle Lock Nut
QU90018 Pyroplex® Protection ES NLGI #2 GC-LB Water Resistant Synthetic Grease
QT4018i Ear Type CV Joint Boot Clamp Pliers

Applications:
Ford:
Bronco II, Ranger, Explorer with Dana 35IFS: 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997.5
Bronco, F-150: 1983.5, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996
F-250 with Dana 44IFS Front Axle: 1983.5, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996
F-250 with Dana 50IFS Front Axle: 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997
F-350: 1983, 1984, early 1985