All 4x4 Truck Parts & Truck Tools

QU40533 GM Dana 60 Right Inner Axle Shaft (Nonstock, Special Order) This short side inner axle shaft is a genuine original equipment replacement inner axle shaft for the right or passenger side on all 1977 to 1991 Chevy or GMC 1 ton 4x4 trucks with...

QU40542U USED Dana 60 Upper King Pin Cap for 1977-1991 Chevy, 1975-1993 Dodge, 1976-1991 Ford, and 1975 IHC heavy duty 3/4 ton and 1 ton 4x4 trucks with Dana 60 or Dana 61 open knuckle, King Pin type front drive axles. Drilled and tapped for grease...

QU40551 New Spicer Dana 60 Hub Drive Gear for 1977-1981 Chevy or GMC and 1978-1979 Ford is a genuine New old Stock (NOS) Spicer OEM replacement Hub Drive Gear for Spicer Dana 60 Spline Mount, Plastic Dial Locking Hubs installed as factory...

QU40559R Reconditioned 10 Tooth Hub Drive Gear for Spicer Plastic Dial Hubs these are good used reconditioned gears with a Black Oxide coating for corrosion protection. This is the later design, coarse tooth gear with 10 internal gear teeth used by Ford...

QU40598 1-1/4" Wide Stepped Gear for Dana 30, Dana 44, and GM 10 Bolt Front Axles. QU40598 was the original design. Outside spline that engages wheel hub is 27/32" wide. These gears are stepped on the outboard side to aid in removal and to space the gear...

QU40615 2 Pinion Limited Slip Clutch Pack for 1985-1997 Ford 10.25" Sterling Rear Axles. Also for 1999-2010 Excursion, F250, F350 10.5" Rear Axles. Limited Supply!

QU40620 3.54 Ratio 1978-1997 Ford Dana 60 Ring and Pinion Set (Non-Stock Special Order) is a genuine Dana, reverse spiral Ring and Pinion set that is unique to the Dana 60 monobeam front axles used in 1978-1979 Ford F250, F350 and 1985-1997 F350 4x4...

QU40632 New Dana 44 Fast Ratio Empty Open Differential Case Kit is a genuine Dana OEM empty differential case kit for Dana 44 front and rear axles with 3.73 or numerically lower gear ratios AND 30 spline axle shafts. These popular diffs were used by...

QU40652U Good Used Right Inner Axle Shaft for 1980-1993 Dodge W150, Ramcharger, Trailduster. This is a new Genuine Dana OEM part. Length from center of hole to end is about 17". Available while supplies last.

QU40673U USED 30 Spline Left Inner Axle Shaft for 1973-1979 Ford 1/2 Ton Dana 44 Front Axles is a used, genuine Dana original equipment drivers or short side inner axle shaft for all 1973-1979 Ford F100, F150 4x4 trucks and 1978-1979 Ford Broncos with...

QU40681 19 Spline Outer Axle Shaft is a genuine Dana OEM part for most 1974-1991 Jeep J10, J20, Wagneer, Cherokee Chief, and Cherokee Dana 44 Front Axles. QU40681 is an exact, OEM replacement Outer Axle Shaft for your full size Jeep J-Series 4x4...

QU40713 1330 Series 1985-1991 Dana 60, Dana 70 Pinion Yoke is a genuine Dana Spicer yoke that fits almost all 1970 to 1999 Dana 60, Dana 61 or Dana 70 front or rear drive axles. The Yoke is made to match universal joints made to Spicer 1330 series...