QU11419 Replacement Hub to Knuckle Bolt Set 1994-1999 Ram 2500, 3500

QU11419 Set of 4 Replacement  Front Hub to Knuckle Bolts for 1994-1999 Ram 2500, Ram 3500 is an affordable, yet quality alternative to our genuine QU10614 original equipment bolts. QU11419 Bolt Set includes 4 Grade 10.9 metric 14mm flanged hex head bolts. The Bolts have 14mm Hex Heads and are plated for protection against corrosion. Made in China.

Also see QU10614 Original Equipment Hub to Knuckle 12 Point Flange Head Bolts.

Dan the Gear Man® Tech Notes:
Only Fits Dana 60
To Remove Hub Assembly
Ball Joints
Right Axle Shaft
Differential Cover Pan Gasket
Seals
Matching Parts
Applications

Tech Note 1: Only Fits Dana 60
QU11419 only fits Dana 60 beam front axles in 1994-1999 Dodge Ram 2500 and Ram 3500 trucks. Four Bolts are used on each side. Use either a 9/16" or 14mm 12 point socket to remove or install the bolts. I always use Threadlocker on the threads. Length from flange face to end is approximately 40mm.

Tech Note 2: To Remove Hub Assembly
The first time a 1994-1999 Dodge Ram 2500, Ram 3500 Dana 60 front axle has to comes apart, it is usually an absolute WITCH to separate the wheel hub assembly from the steering knuckle as Dana did not use any anti-corrosion compound between the wheel hub flange and steering knuckle. Sometimes you can pull the entire hub off with QT1072 puller and sometimes the hub separates and is wrecked. By now, most of these axles have been apart before so the good news is, if your axle was properly reassembled, the hubs should come off with no trouble at all.

Tech Note 3: Ball Joints
On 1994 to 1999 Dodge Ram 2500, 3500 trucks with Dana 60 front axles, the ball joints are pressed into the steering knuckle. If you are replacing your ball joints, I Strongly recommend you use TS4511 Ball Joint Press Set

Tech Note 4: Right Axle Shaft
If you are removing the right axle shaft on an axle with Central Axle Disconnect (CAD), engage four wheel drive before starting disassembly. This will slide the CAD shift collar to the left and onto the differential output shaft splines. If you pull the shaft in 4x2 mode, the shift collar will drop out of position. If this happens, remove the CAD shift unit from the axle and algin the collar. Always replace QU40090 CAD Housing Gasket if you remove the CAD Shift Housing

Tech Note 5: Differential Cover Pan Gasket
It is a good idea to remove the differential cover pan and drain the diff oil before pulling the left axle shaft to prevent gear oil leaking out of the seal after the axle shaft is removed. Available genuine Dana gaskets are:
QU40367 Original Equipment Model 60/70 Fiber Differential Cover Pan Gasket
QU42029 Reusable Model 60 Differential Cover Pan Gasket

Tech Note 6: Seals
Given the era of trucks these bolts fit, if you remove the axle shaft, it is recommended you replace the inner axle seals which can become hard and brittle with age. For Inner Axle Shaft Seal Kits with oil seals and installation tools see: QK4620.

Tech Note 7: Matching Parts
QU10602 Tie Rod or Drag Link Nut
QU40367 Dana Original Equipment Model 60/70 Differential Cover Pan Gasket
QU42029 Dana Reusable Model 60 Differential Cover Pan Gasket
QU40090 CAD Housing Gasket for 2000-2002.5 with Central Axle Disconnect
QU30332 U-Joint with greaseable Hot-Forged Cross
TK40715 Premium non-greaseable U-Joint with Cold Forged Cross
TK40724 Premium greaseable U-Joint with Cold Forged Cross
QK4802 Inner Axle Shaft Seal Kit with Installation Tools
TS4511 Ball Joint Press Set
QT1072 Hub Puller

Applications:
Dodge 4x4 Trucks with Dana 60 Front Axles:
Ram 2500: 1994, 1995, 1996, 1997, 1998, 1999
Ram 3500: 1994, 1995, 1996, 1997, 1998, 1999