- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
QU40930 Midship Center Bearing for GM trucks with 1310 Series Rear U-Joints
40930$42.98QU40930 Midship Center Bearing for GM trucks with 1310 Series rear U-Joints. Bearing Inside Diameter is approximately 1-3/8". Applications:GM:Suburban 60-66Blazer 69-74, 87-94C10 Panel 60-67C20 Panel 67C30 Panel 60-66C10/C20 Pickup 61-86P20... -
QU40934 26 Spline 1350 Series U-Bolt Pinion Yoke for Dana 44, 50 Axles
40934$109.98QU40934 U-Bolt Pinion Yoke for Dana 44 and Dana 50 axles. 26 Spline, 1350 Series. -
QU40936 Front CV Driveshaft Slip Stub for 2.5" x 0.083" Driveshaft Tubing
40936$67.98QU40936 Front CV Driveshaft Slip Stub is a 1-3/8"x16 spline replacement Slip Stub that fits 2-1/2" outside diameter x 0.083" wall thickness front CV driveshafts. Used for many 1970-1978 Fords with 2.5" Front CV Driveshafts on 1970 to 1978 Bronco,... -
QU40953 1410 Series Double Cardan CV Head Assembly
40953$421.98QU40953 1410 Series Double Cardan CV Head Assembly for 2-1/2" x 0.120" Dodge Ram Front Constant Velocity Rear Driveshafts. Max u-joint angle 22 degrees. Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle... -
-
QU40965 Greaseable Front CV Driveshaft for 1980-1993 W150, W250, Ramcharger
748$413.98QU40965 Greaseable Front CV Driveshaft for 1980-1993 Dodge W150, W250, and Ramcharger with NP208 Transfer Case, Dana 44 Front Axle, and any of these transmissions: NP435 4 speed manual, A727 3 speed automatic, or NV4500 5 speed manual.Qty in Cart: 0Price:$413.98Subtotal: -
QU41004 3x.083 1330 Weld Yoke
41004$41.98QU41004 1330 Series Tube Weld Yoke for 3" x 0.083" Driveshafts -
QU41021 Greaseable Spicer 1350 x Detroit 7290 Conversion U-Joint
41021$60.98QU41021 Greaseable Spicer 1350 x Detroit 7290 Conversion U-Joint for special applications. 1350 cup diameter is 1-3/16" and uses external snap rings, lockup dimension is 3-5/8". 7290 cup diameter is 1-1/8" and uses c-clips that fit against the inside of... -
QU42010 Right Front 30 Spline Inner Axle Shaft for 1974-1979 J10, J20, Cherokee Chief
42010$227.98QU42010 New Right Front 30 Spline Inner Axle Shaft for 1974-1979 Jeep J10 truck, J20 truck, and Cherokee Chief. Measures 16-5/8" from center of hole to end. This is a genuine Dana Original Equipment part. Made in U.S.A. Need More Info? Use the handy... -
QU42018U Used Diff Output Shaft for 1980-1983.5 Ford Dana 44IFS
42018$128.98QU42018U Good Used 1980-1983.5 Ford Dana 44IFS Bare Differential Output Shaft available while supplies last. -
QU42020 Pinion Seal for 1983-1997 Bronco II, Ranger with Dana 28IFS Front Axles
42020$18.98QU42020 Pinion Seal for 1983-1997 Ford Bronco II and Ranger with Dana 28IFS front axle. -
QU42022 Pinion Seal for Dana 44 axles on many Jeep TJ and JK Axles
42022$12.98QU42022 Pinion Seal for Dana 44 axles on many Jeep TJ and JK axles.