QU40038 2" ID Flat Spindle Thrust Washer for Front or Rear Axles is the reusable, service replacement Inner Spindle Thrust Washer for 1978-1984 Ford and 1977-1981 GM front Dana 60 axles AND 1946-1981 GM full-floating H052, H072, and GM 14 Bolt rear...

QU40086 Dana 60, Dana 70 Genuine Dana-Spicer Grade 9 Ring Gear Bolt has locking teeth under the hex head to prevent loosening under any load conditions. QU40086 is an exact fit, genuine Dana-Spicer replacement part for most Dana 60, Dana 61, Dana 70, and...

QU11028 Original Equipment Internal Torx® Type Dodge Front CV Driveshaft to Axle Bolt for 2003-2013.5 Dodge Ram 2500, 2003-2012 Ram 3500, and 2004-2010 Ram 1500 Mega Cab is a genuine original equipment part with pre-applied threadlocking compound...

QU40115 Spindle Nut Lock Wedge Key for 1994-2002 Dodge Ram 2500, Ram 3500 Dana 60, 70, and 80 Rear Axles is a genuine Dana original equipment, single use, replacement Wedge that fits in the spindle Key Slot for locking stock type spindle nuts on all 1994...

QU20077 19 Spline Ford Dana 44IFS 3 Piece Axle Shaft Thrust Washer Set is the exact original equipment replacement 3-piece Thrust Washer Set for 1993-1996 Ford Bronco and F150 4x4s PLUS it can be used to replace QU40079 one-piece Thrust Washer used...

QK4727 4 Slot Dana 30, Dana 44, GM 10 Bolt Front Spindle Nut Kit includes one each genuine original equipment QU40004 Inner Spindle Nut, QU40060 Spindle Nut Lock Washer, and QU40031 Outer Spindle Nut which fit many Dana 30 (Ford Bronco) Dana 44 (All...

QK4883 Front Pinion Seal and Wear Sleeve Kit for Dodge Ram American Axle 9-1/4" Front Axle has all the genuine original equipment AAM parts you need to stop that pesky oil leak from your front axle pinion flange. Kit includes double lip Pinion Seal,...

QU11061 Vacuum Supply Line Harness for 1998-2002 Dodge Ram with CAD is a genuine original equipment vacuum harness that runs from the engine back to the transfer case vacuum switch and then down to the transmission cross member on 1998-2002 era Dodge...

QU20971 Rear Axle Shaft Bolt with Hex Head (no flange) for Ford F250, F350 is a USA Made, Grade 8  that fits 1972-1997 Ford F250, and 1973-1997 Ford F350 with Dana 60 (1972-1985), Dana 70 (1973-1985) and Ford Sterling 10.25" (1985-1997)...

QU10847 Rear Axle Shaft Flange Gasket for AAM 1050, 1150, and 1180 Full Floating Rear Axles is an advanced fiber composition, non-reuseable axle shaft flange to wheel hub gasket for all 2003-up Dodge Ram and Ram 2500 and Ram 3500 trucks equipped with the...

QU40105 Inner Axle Shaft Seal for CAD Axles Genuine original equipment seal fits most Dodge and Plymouth full-size 4x4's equipped with Dana-Spicer 44 and Dana-Spicer 60 front axles and vacuum controlled Central Axle Disconnect (CAD) systems and 1984-1987...

QK4647 Front Axle Inner Oil Seal Remover Set with 1-3/4" Driver Tip for many common front inner axle oil seals is a real time saver! Use to remove the inner axle shaft oil seals on any 4x4 solid front drive axle with axle housing tube...