QK4932 Front Inner Axle Shaft Seal Kit for Jeep Wrangler JK Super 30

QK4932 Front Inner Axle Shaft Seal Kit for All 2007-2017 Jeep JK Wranglers with Super 30 Front Axles Makes short work of installing new inner axle shaft seals in your 2007-2017 Wrangler JK. Quickly and easily install those all-important Inner Axle Shaft Seals without damaging the seal! Our unique installer design will press in your new Inner Axle Seals without damage because the CNC Precision Machined Installation Tool cups the seal so force is only applied on the steel seal shell. Axle Shafts worn or rusty? No problem! Our Install Tool allows you to install either or both Inner Axle Seals to a variable depth to miss grooves worn in your inner axle shafts. Kit includes two axle shaft oil seals and Install Tool Set.

Already have the Seals and just need the Tools? See TS4932 for Tool Set only.

This kit includes the QU40812 Conventional, Single Lip Inner Axle Seals. For a Kit that includes the newer design D440600 Inner Axle Shaft Oil Seals, please see TK4993.

Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!

Dan the Gear Man® Tech Notes:
Kit Components
Must Remove
Clean Axle Tubes
Lubricate Seals
Inspect for Wear or Damage
Adjustable Depth
Matching Parts
Applications

Tech Note 1: Kit Components
QK4932 Includes:
(2) QU40812 Inner Axle Shaft Oil Seals
QT1203 Axle Seal Installer
QT1186 Thrust Plate
QT1189 Press Screw Assembly

Tech Note 2: Must Remove
For 2007-2017 Jeep JK Wrangler Super Dana 30 front axles, two identical axle shaft seals are used. One QU40812 Seal is pressed in the inboard end of each axle tube next to the differential. It is impossible to replace the seals from the outside! You MUST remove the hubs, axle shafts, and differential to replace these seals. QT1032 differential case spreader is definitely recommended but not absolutely required for differential removal/installation.

Tech Note 3: Clean Axle Tubes
After removing the old seals (See optional Removal Tools QK4647, TS4863, QT1144), thoroughly clean the axle tubes to remove crud, grit, and scaly rust.

Tech Note 4: Lubricate Seals
Lubricate the Seal Lips with clean grease before installing the differential to provide initial lubrication. Install the axle shafts dry to minimize the chances of picking up residual grit inside the axle tubes as you slide the axle shafts into position.

Tech Note 5: Inspect for Wear or Damage
When replacing your inner axle seals, ALWAYS inspect your Ball Joints, Axle Universal Joints, Differential Bearings, and Wheel Hubs for wear or damage. The extra time needed to replace these components is minimal since you already have the axle apart to do the axle seals.

Tech Note 6: Adjustable Depth
QK4932 uses QT1203 adjustable depth installer which allows you to offset the seal to miss a worn spot on the axle shaft. This is a valuable feature, however, YOU have to determine the final depth of the seal. If you are not careful, it is unlikely but possible to seat the seal too deep with which can put the seal beyond the machined seal surface of the axle shaft.

Tech Note 7: Matching Parts
Parts you may also need for 2007-2017 Jeep JK Wrangler
D440258 Hex Nut
D440576 JK Ball Joint Kit
TK40712 Non-Greaseable Axle U-Joint
QU90007 Greaseable Axle U-Joint
QU40236 Dana 25/27/30 Diff Cover Gasket
QU42027 Dana 25/27/30 Reusable Diff Cover Gasket
S82194 Ultra Gray RTV Sealant
QT1032 Differential Case Spreader

Applications
Jeep
JK Wrangler with Dana Super 30 Front Axle: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017