QK4807 Depth Controlled Ford Dana 60 Inner Axle Seal and Tool Kit

QK4807 Inner Axle Seal and Tool Kit for Ford 1999-Current Dana 60 and Super 60 Front Axles include QU40244 seals with slinger that are specific to 1999-2010, but the same tools and seals work equally well on 2011 to current Dana Super 60 axles in F250, F350, F450, and F550 4x4s. QK4807 Fixed Depth will quickly and easily press in new Inner Axle Seals without damage because the installation tool cups the seal so the force is only applied on the outer shell.

QK4807 uses QT1128 Model 60 Seal Installer with a depth stop which will stop when your new seal is installed to the original depth. Makes life simple. Please See Tech Note 5 Below!

Also available: QK4644 uses QT1126 Dana 50/60 Inner Axle Seal Installer which does not have a depth stop. You have to watch how deep you install the seal. See Tech Note 4 Below!

For 1999-2004 Super Duty® trucks is our optional, color illustrated, step-by-step Tech Service Bulletin TSB4643. The TSB4643 applies specifically to 1999-2004 Super Duty®. For 2005 and newer Super Duty® trucks, Inner Seal Replacement is identical but disassembly and reassembly is a little different as far as the hub and rotors.

For Tool Sets without Seals: TS4644 and TS4807

Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!

Dan the Gear Man® Tech Notes:
Fixed Depth Kit Includes
Must Remove
When Installing Seals
Model 60 only
4x4 Tech Publications
Seal Remover Tool
When Replacing
Effective in 2011
Available Tool Sets
Matching Individual Parts for 1999-2004 Super
Matching Parts for 2005-2016 F250, F350
Matching Publications and Tools
Applications

Tech Note 1: Fixed Depth Kit Includes:
(2) QU40244 Axle Shaft Seals
QT1128 Fixed Depth Dana 60 Seal Installer See Tech Note 5 below!
QT1130 Dana 60 Thrust Plate
QTA1133 Press Screw Assembly

Tech Note 2: Must Remove
Your brakes, wheel hubs, axle shafts, and differential must be removed from the housing to replace your QU40244 Inner Axle Shaft Seals. For Ford 1999-2004 Super Duty®, please refer to these 4x4 Tech Publications for service procedures:
TSB4643 Includes 5 pages of Step-by-Step procedures with 17 full-color photographs. Covers axle shaft removal, inner axle seal replacement, axle shaft reassembly, differential oil specs, differential gear backlash, torque specs and wrench sizes for fasteners. Explains in text and photos how to change the Inner Axle Shaft Oil Seals located next to the differential. Includes detailed axle shaft oil seal replacement procedures, tool recommendations, and torque specifications that you need to correctly perform inner seal replacement plus check the gear backlash on your Ford Excursion or 1999-2004 Ford F250, F350, F450, or F550 Super Duty® 4x4 Dana Spicer Model 50 or Model 60 front axle. *Note: The TSB4643 only applies specifically to Ford Excursion and 1999-2004 Super Duty®. For 2005 and newer Super Duty trucks, Inner Seal Replacement is identical. The disassembly and reassembly are different as far as the hub and rotors.
TM4637 Front Axle Tech Manual for Ford Excursion and 1999-2004 Super Duty is a 17 page, color illustrated, step-by-step printed shop repair manual that includes our four Tech Service Bulletins plus Front Axle Exploded Views. TM4637 covers: Front Hub Service (TSB4594), Axle Shaft Service (TSB4610), Ball Joint Service (TSB4591), and Inner Axle Seal Replacement Service (TSB4643), including torque specs all in one manual.
TM4688 4x4 Hub, Axle Shaft, Ball Joint, and Axle Shaft Seal Service Manual includes 76 full color printed tech pages with precise and detailed service instructions, plus a color photo for every step. (Includes all info in TM4637.) Close to 400 color photographs, color Exploded Views and Parts Guide. Comprehensive service information for replacing Front Axle Shaft Oil Seals, Axle Universal Joints, Ball Joints, Knuckle Seals, Axle Shaft Needle Bearings, Wheel Hubs, and Hub locks. Also covers basic Front Brake Service. Additionally includes complete torque specs, and tool recommendations.

Tech Note 3: When Installing Seals
The inner axle seals used on 1999 and newer Model 50 and 60 Ford front axles are interchangeable, however, the depth the seals are installed in the housing is different. With the QK4644 Kit, you get QT1126 Adjustable Depth Seal Installer which is made to work with both Model 50 and 60 axles. It's less expensive, but you have to know when the seal is at the correct depth.

To get the correct seal depth when using QT1126 with a Model 60 axle do this: Before you take out the old seals, place QT1126 Seal Installer in the old seal and scribe a mark on the tool at the axle bore face. During installation, just press the seal in until the scribed mark lines up with the bore face and your new seal is installed to the correct depth!

If you want to use QK4644 on a Dana 50 axle, you will also need optional QT1129 Dana 50 Thrust Plate.

Choose QK4644 Kit for price and versatility, keeping in mind you have to stop pressing the seal in when it is to the correct depth. However, YOU MUST be careful you do not set the seal TOO DEEP which may place the seal beyond the axle shaft seal surface!

Tech Note 4: Model 60 only
QK4807 uses QT1128 Model 60 specific Depth Stop Seal Installer which has a raised flange on it that will stop against the axle bore face when the seal is at the correct depth. This is a more fool-proof setup than QK4644, but it's a little more expensive, and you cannot use this Installer on a Model 50 axle. Choose QK4807 for simplicity & even quicker installation!

Tech Note 5: 4x4 Tech Publications
QU40244 is item 35 in the Differential Parts Full Color Exploded View that is included in these 4x4 Tech Publications for Ford Excursion and 1999-2004 Super Duty®: TM4637, and TM4688

Tech Note 6: Seal Remover Tool
Once the axle is disassembled, the old seals can be easily removed with our QK4647 Seal Remover Tool Set or another suitable tool such as a length of sturdy pipe that will fit inside the axle tube and oil guide. You will also need to clean the inside of the axle tube to remove dirt and crud that could get pushed into your new seal during reassembly. For 1999-2004 vehicles, QK4647 is made it fit through QU20039 Plastic Axle Shaft Guides which are located in the axle tubes just outboard of the inner axle shaft oil seals.

Tech Note 7: When Replacing
When replacing your inner axle seals, ALWAYS inspect your Ball Joints, Axle Universal Joints, Differential Bearings, Outer Axle Shaft Support Bearing, and Wheel Hubs for wear or damage. The extra time needed to replace these components is minimal since you already have the axle apart to do the axle seals. Also, the large diameter seals on each outer axle shaft are not reusable and must be replaced with a new one using a special tool to prevent water infiltration and/or vacuum loss.
QU40233 1999-2002 Outer Axle Shaft to Knuckle Seal
QU20035 2003-2004 Outer Axle Shaft to Knuckle Seal
QT1515 Axle to Knuckle Seal Installer 1999-2004
QK4610 1999-2002 Hub and Knuckle Seal Kit with QT1515
QK4846 2003-2004 Hub and Knuckle Seal Kit with QT1515
QU20052 2005-2016 Outer Axle Shaft Knuckle Seal
TS1530 Axle to Knuckle Seal Installer for 2005-2016 F250, F350
TS1531 Axle to Knuckle Seal Installer for 2005-2016 F450, F550
QK4678 2005-2016 F250, F350 Hub and Knuckle Seal Kit with TS1530
QK4681 2005-2016 F450, F550 Hub and Knuckle Seal Kit with TS1531

Tech Note 8: Effective in 2011
Effective with the 2011 model year, Ford replaced QU40244 Inner Axle Shaft Seal supplied in the Kits on this page, and which features an integral oil slinger on the diff side plus a generous axle shaft guide on the outboard side with QU20463 Seal that has no slinger and only a small shaft guide. Functionally, the seals are interchangeable on 1999 to current Ford Dana 50, Dana 60, and Dana Super 60 front axles, but they do require different installers. Personally, I prefer the earlier QU40244 Seal, but they are both high-quality oil bath seals that will keep oil in your diff for years if properly installed.

If you would prefer QU20463 Seal, the correct Installer is QT1222 which is available separately or in these Tool Sets and Kits for Ford:
TS4982 Tool Only Set for 1999-2005 Dana 50
QK4982 Inner Axle Seal and Tool Set for 1999-2005 Dana 50
TS4983 Tool Only Set for 1978-current Dana 60, Dana Super 60
QK4983 Inner Axle Seal and Tool Set for 1978-current Dana 60, Dana Super 60

Tech Note 9: Available Tool Sets
Already have the Seals? See TS4644 and TS4807 Tool Sets Only.

Tech Note 10: Matching Individual Parts for 1999-2004 Super Duty
QU20677 Left Axle Shaft Assembly
QU20676 Right Axle Shaft Assembly
QU40385 3 Piece Outer Axle Shaft Thrust Washer Set
QU40155 Outer Axle Shaft Snap Ring
QU40242 Inboard Thrust Washer for Outer Axle Shaft
QU40143 Needle Bearing, Outer Axle Shaft Support
QU20023 Wheel Hub to Knuckle O-Ring
QU20044 Hublock O-Ring
QU20043 Hublock Snap Ring
QU20039 Inner Axle Shaft Oil Guide
QU40243 Dust Seal for Inner Axle Shaft (Goes next to Yoke)
QU40233 Unshielded Outer Axle to Knuckle Seal 1999-2002 (will also fit 2003-2004)
QU20035 Shielded Outer Axle to Knuckle Seal 2003-2004
QU30332 Standard Greaseable Axle U-Joint
TK40715 Premium Factory Lubed Axle U-Joint
TK40724 Premium Greaseable Axle U-Joint
QU40174 Dana OEM Ball Joint Set for 1 Side
QU40384 Brake Splash Shield
QU20053 Brake Caliper Anchor Plate to Steering Knuckle Bolt
QU40367 Spicer OEM Dana 60/70 Differential Cover Gasket
QU42029 Spicer Reuseable High-Performance Dana 60 Cover Gasket
S82194 Gray RTV Sealant for Diff Cover (in lieu of gasket)
QU20081 Nut, Wheel Hub to Steering Knuckle
QU20145 Auto Hublock Assembly
QU20339 Manual Hublock Assembly
Ford Shop Manuals

Tech Note 11: Matching Parts for 2005-2016 F250, F350
QU20305 Right Axle Shaft Assembly F250, Standard Width F350
QU20582 Left Axle Shaft Assembly F250, Standard Width F350
QU40538 1st Design Dust Seal for Inner Axle Shaft (Goes on Shaft)
QU20049 2nd Design Dust Seal for Inner Axle Shaft (Goes on Housing)
QK4680 Gasket and Seal Kit for Wheel Hubs and Outer Axle
QU20052 Outer Axle Shaft to Knuckle Seal
QK4678 Knuckle and Hub Seal Kit with TS1530 Seal Installer
QU20045 Wheel Hub to Knuckle O-Ring
QA20073 Bearing Kit, Outer Axle Shaft Support
QU20046 Factory Hublock Gasket, O-Ring, and Screw Kit
QU20081 Nut, Wheel Hub to Steering Knuckle
QU30332 Standard Greaseable Axle U-Joint
TK40715 Premium Factory Lubed Axle U-Joint
TK40724 Premium Greaseable Axle U-Joint
QU40579 Dana OEM Ball Joint Set
TK42057 Dynatrac Heavy-Duty Rebuildable Ball Joints
QU40367 Spicer OEM Dana 60/70 Differential Cover Gasket
QU42029 Spicer Reuseable High-Performance Dana 60 Cover Gasket
S82194 Gray RTV Sealant for Diff Cover (in lieu of gasket)
QU56026 Black and QU56027 Chrome Warn Lockout Hub Sets
Ford Shop Manuals

Tech Note 12: Matching Publications and Tools
TM4688 1999-2004 Front Axle Service Manual 76 Pages
TM4637 1999-2004 Front Axle Tech Manual 19 Pages
TSB4643 Inner Axle Seal Replacement Bulletin 5 Pages
TSB4644 1999-2004 Front Axle Exploded View and Parts Guide 14 Pages
QT1515 Knuckle Seal Installer 1999-2004
TS1530 Knuckle Seal Installer for 2005-2016 F250, Standard Track F350
TS1531 Knuckle Seal Installer for 2005-2016 F450, F550, Wide Track F350
QT1129 Thrust Plate for Dana 50 Axles (Use with QK4644 for Dana 50 Seal Installation)
QK4647 Seal Remover Tool Set
QT1032 Differential Case Spreader

Applications:
FORD:
F-250 All with Model 60 Front Axle (See QK4643 for Model 50 axles): 1999, 2000, 2001, 2002, 2003, 2004
F-350 Single Rear Wheel All with Model 60 Front Axle (See QK4643 for Model 50 axles): 1999, 2000, 2001
F-350 with Single Rear Wheel: 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018
F-350 all with Dual Rear Wheel: 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018
F450, F-550: All 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018