YY D60-1330-29S 1330 Series Pinion Yoke for Dana 60 and Dana 70 Axles

YY D60-1330-29S 1330 Series Pinion Yoke for Dana 60 and Dana 70 Axles replacement yoke that fits almost all 1970 to 1999 Dana 60, Dana 61 or Dana 70 front or rear drive axles. The Yoke is made to match universal joints made to Spicer 1330 series specifications. This Yoke directly replaces the stock 1330 pinion yoke on some 1977 to 1979 Ford F-250 and F-350 trucks, but the primary application is to retrofit later Ford Dana 60 axles that used an out of production QU20179 1330F pinion Yoke. Also commonly used for Chevy, Dodge, and GMC Dana 60 front axles to take 1330 series universal joints instead of the undersized stock 1310 or 7260 series front u-joints supplied as original equipment. Limited supply.

QU40509 is the genuine Dana Spicer 1330 Yoke

Also order QU40735 Strap and Bolt Kit to secure your universal joint to the yoke.

Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!

Dan the Gear Man® Tech Notes:
29 Spline Pinion
1993 & Earlier Applications
1/4” Shorter
1994-2002 Dodge
Matching Parts
Applications

Tech Note 1: 29 Spline Pinion
  YY D60-1330-29S is 29 spline Dana 60, Dana 61, or Dana 70 pinion yoke made to couple with driveshaft universal joints made to Spicer 1330 specifications. A 1330 u-joint is a 1-1/16" cup diameter, external snap ring type joint that has an overall width of 3-5/8". See TK40721 and QU40774 universal joints.

Tech Note 2: 1993 & Earlier Applications
For 1993 and earlier applications, matching pinion seal is QU40097 and Pinion Nut is QU40022. See QU40356 Crush Sleeve for later model Dana 60 axles in Dodge and Ford trucks that use a collapsible spacer instead of shims to set pinion rotating preload. All 1993 and earlier axles and many 1994 and newer Ford or GM Dana 60 axles use reusable pinion shims to set pinion bearing rotating preload. Never back off the nut to try and reduce the rotating preload of the pinion!!!! See TM4400 or the factory shop manual for your truck for rotating preload specs.

Tech Note 3: ¼” Shorter
YY D60-1330-29S is 1/4" shorter than the original pinion yoke used on 2000-2002 Dodge Ram 2500 and Ram 3500 4x4 Dana 60 front axles. YY D60-1330-29S can be used in 2000-2002 Dodge Ram Dana 60 axles that originally used discontinued QU40379 yoke IF you remove the stamped steel slinger AND your driveshaft slip yoke can safely extend 1/4".

Tech Note 4: 1994-2002 Dodge
On 1994 to 2002 Dodge Dana 60 axles, pinion rotating preload is set by a crush sleeve (QU40356). When tightening your pinion nut, you have to be very careful as it will only take a small movement of the nut to go from too loose to too tight. If you over tighten the nut, you MUST get a new spacer and start over!!! Never back off the nut to try and reduce the rotating preload of the pinion!!!! See TM4400 or the factory shop manual for your truck for rotating preload specs.

Tech Note 5: Matching Parts
Exploded View XV1001 1975-1989 Dodge Dana 60/61 Front Axle
Exploded View XV1006 1977-1991 Chevy & GMC Dana 60 Front Axle
QU40356 Crush Sleeve (1994-up Dodge Ram Dana 60)
QU40095 Outer Pinion Oil Slinger
QU40097 Pinion Seal up to 1999
QU40348 Early 2000 to 2001.5 Dodge Ram Pinion Seal
QU40402 2001.5 to 2002 Dodge Ram Pinion Seal with Flanged Shell
QU40397 Pinion V-Seal for 2000-2002 Dodge Ram
QU40022 Pinion Nut
QU40023 Pinion Washer
QU40735 U-Joint Strap/Bolt Kit
TK40721 or QU40774 Universal Joints
S9978 Medium Strength Threadlocker

Applications:
Dana 60, Dana 61, Dana 70: 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999
Ford F-250 and F-350 trucks: 1977, 1978, 1979