TS1184 Front Axle Shaft Oil Seal Remover Set For Dodge RAM with CAD

TS1184 Front Axle Shaft Oil Seal Remover Set For Dodge RAM with CAD is a real time saver! Use to remove the inner axle shaft oil seals on most full size Dodge 4x4s with Dana Spicer Model 44 (1989-2001) or Model 60 (1994-1999) solid front drive axles equipped with the vacuum controlled Central Axle Disconnect (CAD) system. This handy tool knocks out those tricky inner axle shaft seals in a flash! Kit includes QT1145 drive rod, QT1214 seal remover, and Grade 8 jam nut. QT1145 is made from U.S. produced 1.25" diameter steel and has wrench flats machined in the shaft. USA Made. Finish on rod may be either light Brown Oil Finish or Black Oxide (no choice)

Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!

Dan the Gear Man® Tech Notes:
Tool Set Components
Additional Tools
Seals
Use Proper Tools
Tool Attachments
Remover Tool Sets
Applications

Tech Note 1: Tool Set Components
TS1184 Tool Set Includes:
QT1145 Long Driver Handle
QT1214 2" Seal Remover
QU95008 Grade 8 Hex Nut

Tech Note 2: Additional Tools
Do you also need to remove the front axle shaft oil seals on trucks without CAD? Just add our QT1151 Extension Rod or purchase TS4862 Remover Set! Working on 2000-2002 Ram 2500 or Ram 3500 with CAD? If so, order our QT1216.

Tech Note 3: Seals
The diff side inner axle seal is located right next to the differential, and it is impossible to replace without disassembling the axle up to and including the differential. Once everything except the pinion gear is removed, you drive the seals inward until they drop into the housing. The CAD side seal is pressed in the housing next to the CAD housing. The CAD side hub and axle shafts must be removed to replace the seal.

Tech Note 4: Use Proper Tools
Once the seals are removed, you need to clean any dirt, grit or crud out of the diff housing and axle tubes. After that, you can install your new seals. Seal installation is best done with our tooling made for your specific application. Sometimes you can get by with makeshift installers you cobble together, but in most cases, using makeshift tools just guarantees you get to do the job all over again.

Tech Note 5: Tool Attachments
Our currently available attachments are:
QT1144: Fits axle tube inside diameters of 1.75" and larger. Max seal ID with rubber lip seals is 1.5", max seal diameter with oil bath type seal is 1-9/16" (used on Ford Excursion and Super Duty® Model 50 and 60 monobeam axles from 1999 to 2004). This remover fits most Model 30, Model 44, and GM 10 Bolt front axles. The outside diameter is made to fit through the inner plastic axle guides used on 1999-2004 Ford Super Duty and 2000-2005 Ford Excursion.
QT1214: Fits axle tube inside diameters of 2.00" and larger. Max seal ID 1-3/4". This remover fits most Model Model 44, Model 50, Model 60, Model 61, Model 70, AAM 925, and GM 10 Bolt front axles with 3" or larger outside diameter axle tubes.
QT1216: Fits axle tube inside diameters of 2.25" and larger. Max seal ID 2". This remover is primarily made to remove the large bore, right side seal on 2000-2002 Dodge Ram 2500 and Ram 3500 trucks with vacuum controlled Central Axle Disconnect (CAD). It will also work on all to remove the left seals on the same model trucks, plus either seal on all 2002 and newer Dodge Ram 2500 and Ram 3500 models and all 2005 and newer Ford Super Duty® F-250, F-350, F450, and F-550 4x4s.
For Smaller Axles: For axle tube diameters between 1.50" and 1.75", you just use QU95007 nut as the remover.

Tech Note 6: Remover Tool Sets
Our Front Axle Shaft Oil Seal Remover Tool Sets are:
QK4647: Includes TS4863 Rod Assembly and QT1144 Remover (Most smaller axles plus Ford Excursion and 1999-2004 Super Duty®)
TS1184: Includes QT1145 Rod, QU95007 Nut, and QT1214 Remover (Specific Kit for most Dodge with CAD)
TS4862: Includes TS4863 Rod Assembly and QT1214 Remover (Most larger axles except 2000-2002 CAD equipped Ram 2500 and Ram 3500 or Ford Excursion and 1999-2004 Super Duty®)

Applications
Dodge Ram:
W-150 4x4 with Vacuum Controlled Central Axle Disconnect Front Drive Axle: 1989, 1990, 1991, 1992, 1993
W-250 gas engine 4x4 with Vacuum Controlled Central Axle Disconnect Front Drive Axle: 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001
1500 4x4 with Vacuum Controlled Central Axle Disconnect Front Drive Axle: 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001
2500, Ram 3500 4x4 with Vacuum Controlled Central Axle Disconnect Front Drive Axle: 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999