Description
QU10703 GM NV4500 5 Speed Manual Transmission Shift Tower is a direct replacement Shift Tower for all 1995-2003 Low-Rise, Long-Shift GM New Venture NV4500 5 speed manual transmission shift covers. Also fits all 1998-2005 Dodge Shift Covers. 16mm fine thread shifter connection. Imported.
Also see QK1126 GM Shift Tower Kit.
Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!
Dan the Gear Man® Tech Notes:
Fits
Tower Replacement Parts
Specs
Special Tools
Matching Parts
Applications
Tech Note 1: Fits
QU10703 Shift Tower will fits all the GM C and K series trucks with NV4500 5 speed manual transmissions from 1995 through 2000. When a heavy-duty version of the Silverado/Sierra series trucks was introduced in the 2001/2002 model years, a 2" body raise required a higher cover and tower. The GM parts information is a bit vague on the exact timing of when the low rise transmissions were phased out, but I find no reference to the low rise tower after the 2002 model year for 4x4 trucks.
Tech Note 2: Tower Replacement Parts
New Venture purchased complete shift towers from another vendor. New Venture never offered individual shift tower replacement parts and rubber seals nor have any aftermarket suppliers.
Tech Note 3: Specs
All 1998-2005 Dodge with 14mm coarse thread shift stub and 1995-2000 GM with 16mm fine thread shift stub NV4500 Shift Towers are physically interchangeable on the covers. In 2001 GM introduced the GMT 800 2500HD and 3500HD Chevy Silverado and GMC Sierra trucks. Vehicle Identification Number based (VIN) GM electronic parts books show two shift covers and towers for 2001-2002. The difference is the height of the cover shift tower base and length of the shift tower stub. The early cover as used for year 2000 and prior plus some 2001-2002 has a shift tower base that is about 3/4" high and it uses a short shift stub. The 2001 and later cover has a base that is approximately 1" high, accepts towers with a longer stub, and it was used on all the 2003-2007 Silverado and Sierra trucks. The Dodge and early GM towers are not interchangeable with late GM shift towers.
Tech Note 4: Special Tools
Need Torque Specs or Rebuild procedures? Order my 116 page, full color illustrated TM1003 NV4500 Rebuild Manual. You will need some special tools to correctly service your NV4500 Transmission. The chart below lists our current NV4500 Special Tools for popular models.
TOOLS for SPECIFIC NV4500 MODELS |
||||||
Component | 23 Spline Dodge 4x4 NV4500LD |
29 Spline Dodge 4x4 NV4500HD |
30 Spline Dodge 4x2 NV4500LD |
31 Spline Dodge 4x2 NV4500HD |
32 Spline GM 4x4 |
35 Spline GM 4x2 |
Mainshaft Nut | QT2002 | QT2001 QT2036 |
QT2002 | QT2001 QT2036 |
QT2002 QT2028 |
1-1/2" Hex Socket |
Mainshaft Holding | NLA | QT2000 | NLA | QT2011 | N/A | N/A |
5th Gear Nut Torx® Cross Bolt |
N/A | QT9205 | N/A | QT9205 | N/A | N/A |
Output Seal Installer | N/A | QT1801 | N/A | QT2058 CALL |
Not Used | Not Used |
Tailshaft Bushing Remover and Installer | Not Used | Not Used | Not Used | QT2044 | Not Used | Not Used |
TOOLS For ALL NV4500 MODELS |
||||||
Countershaft Front Bearing Cup Installer |
QT1802 | Use with QT1101 or QT1119 Driver Handle. Also can use flat side to install Dodge 4x4 Rear Output Seal | ||||
Countershaft Front Bearing Installer | QT2004 | Can also use to press 3-4 Synchro Hub on original equipment mainshafts | ||||
Input Bearing & Countershaft Rear Bearing Installer | QT2005 | Can also use to install Input Seal | ||||
Input Bearing Cup Installer | QT1801 | Use with QT1100, QT1101, QT1116, or QT1119 Driver Handle. | ||||
Countershaft Support | QT2006 | Use to support front of countersahft when installing countershaft rear bearing | ||||
1-2 Synchronizer Support | QT2008 | Use to support 1-2 synchronizer hub during synchronizer assembly | ||||
10mm 1/2" Drive 12 Point Socket | QT1020 | USA Made Impact Socket for Factory Tailshaft Housing Bolts | ||||
Long Shank Punch for Shift Lug | QT9300 | 3/16" x 8" Shank for 5th Gear Shift Lug Roll Pin |
Tech Note 5: Matching Parts
(4) QU10155 Spacer/Bushing
(4) QU10156 Bolt
QU10157 Metal/Rubber Tower Spacer Plate
QU90005 RTV Sealant
QU10706 Shift Cover Assembly
Applications:
Chevy and GMC:
Silverado and Sierra Trucks with MT8/MW3 5 Speed NV4500 Manual Transmissions: 1994, 19945, 1996, 1997, 1998, 1999, 2000
Silverado HD and Sierra HD Trucks with MT8/MW3 Low Rise Covers: 2001, 2002
Warranty
Product Reviews
-
shifter
fit good
Delivery & Returns
Shipping times are estimated in your cart.
More info can be found at the link below.