null

QU10054 1"-19 Spline 1992-1993 Dodge NV4500 Input Shaft

Torque King
No reviews yet Write a Review
$272.98
SKU:
10054
Condition:
New

Description

QU10054 1"-19 Spline 1992-1993 Dodge NV4500 Input Shaft (Main Drive Gear) New Old Stock (NOS) Genuine original equipment New Venture 1" x 19 spline input shaft for 1992-93 D and W series trucks with gas engines and New Venture NV4500 5 speed manual transmissions. USA Made.

Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!

Dan the Gear Man® Tech Notes:
Shaft Specs
Common Failures
Gear Strength
Bearings

NV4500 Tools
Matching Parts
Synchronizer Parts
Applications

Tech Note 1: Shaft Specs
QU10054 is a 22 tooth 1" x 19 spline input shaft. The matching Countershaft Gear must have 38 teeth. The tip for the pilot bearing is 3/4".  Combined Input Shaft and Mainshaft End-Play should be set at 0.002"-0.006".

Tech Note 2: Common Failures
The majority of NV4500 Input shaft failures are caused by one or more of the following:
#1. Failed clutch pilot bearing or bushing which chews up the input tip and can cause gear tooth breakage from misalignment between the engine and transmission.
#2. Running the transmission low on oil or with the wrong oil.
#3. Excessive horsepower which can cause either tooth breakage or the shaft to twist off.
#4. Bellhousing Index Hole off center and/or Bellhousing to block alignment pin(s) missing. A Dodge gasoline engine bellhousing with a bellhousing to transmission index hole that is more than 0.010" off center from the crankshaft centerline should be replaced or corrected by the use of offset dowels.

Tech Note 3: Gear Strength
The New Venture NV4500 transmission was factory rated at 450 LB.-FT. of input torque. The infamous fifth gear issue which plagues Diesel powered trucks is not a significant issue with the Dodge NV4500 which was only used with gas V8 engines. NV4500 performance and longevity is excellent with stock gasoline engines. I have seen some twisted off 23 spline 4x4 output shafts with modified gas engines, but that problem can easily be solved by installing a NV4500HD 29 spline output shaft and mainshaft 5th gear.

There are claims that cryogenically treating NV4500 gears will increase gear strength as much as 30%. Unfortunately, there does not seem to be any peer-reviewed documentary evidence to support those claims. Cryogenically treating gears is primarily a cold-hardening process that changes the molecular structure of steel to decrease wear while retaining or increasing hardness. If properly done, it is probable the cryogenic treatment process does slightly increase the impact and fatigue resistance of NV4500 gears, but not enough to significantly increase the ability of an NV4500 transmission to reliably handle more than 600 Lb.-Ft. of input torque especially considering the maximum factory torque rating of the NV4500HD transmission is only 460 Lb.-Ft..

Tech Note 4: Bearings
The New Venture NV4500 Input Shaft is designed to use three bearings. The input shaft is supported by a pressed-on Timken® high-performance Tapered Bearing Set. The back of the input shaft is bored for straight, caged roller bearing. The back face of the input shaft is ground flat for contacting the mainshaft to input thrust bearing. Another design feature of NV4500 input shafts is the 4th gear clutch ring is not an integral part of the input shaft, instead it is a slip fit to splines machined behind the input gear teeth. Incidentally, with the NV4500, 4th "gear" is simply a direct connection between the input shaft and output shaft with no power transfer through the countershaft.

Tech Note 5: NV4500 Tools
Need Torque Specs or Rebuild procedures? Order my 116 page, full color illustrated TM1003 NV4500 Rebuild Manual.

You will need some special tools to correctly service your NV4500 Transmission. The chart below lists our current NV4500 Special Tools for popular models.

TOOLS for SPECIFIC NV4500 MODELS

Component 23 Spline
Dodge 4x4
NV4500LD
29 Spline
Dodge 4x4
NV4500HD
30 Spline
Dodge 4x2
NV4500LD
31 Spline
Dodge 4x2
NV4500HD
32 Spline
GM 4x4
35 Spline
GM 4x2
Mainshaft Nut QT2002 QT2001
QT2036
QT2002 QT2001
QT2036
QT2002
QT2028
1-1/2" Hex
Socket
Mainshaft Holding NLA QT2000 NLA QT2011 N/A N/A
5th Gear Nut
Torx® Cross Bolt
N/A QT9205 N/A QT9205 N/A N/A
Output Seal Installer N/A QT1801 N/A QT2058
CALL
Not Used Not Used
Tailshaft Bushing Remover and Installer Not Used Not Used Not Used QT2044 Not Used Not Used

TOOLS For ALL NV4500 MODELS

Countershaft
Front Bearing Cup Installer
QT1802 Use with QT1101 or QT1119 Driver Handle. Also can use flat side to install Dodge 4x4 Rear Output Seal
Countershaft Front Bearing Installer QT2004 Can also use to press 3-4 Synchro Hub on original equipment mainshafts
Input Bearing & Countershaft Rear Bearing Installer QT2005 Can also use to install Input Seal
Input Bearing Cup Installer QT1801 Use with QT1100, QT1101, QT1116, or QT1119 Driver Handle.
Countershaft Support QT2006 Use to support front of countersahft when installing countershaft rear bearing
1-2 Synchronizer Support QT2008 Use to support 1-2 synchronizer hub during synchronizer assembly
10mm 1/2" Drive 12 Point Socket QT1020 USA Made Impact Socket for Factory Tailshaft Housing Bolts
Long Shank Punch for Shift Lug QT9300 3/16" x 8" Shank for 5th Gear Shift Lug Roll Pin

 

Tech Note 6: Matching Parts
Matching Parts for QU10054 Input Shaft:
QU10049 or QU10702 4th Gear Clutch
QU10124 Timken® High Performance Input Bearing
QU10125 Timken® High Performance Input Bearing Cup
QU10133 NV4500 Input Pocket Bearing
QU10134 NV4500 Input Thrust Bearing
QU10126 Input Seal
QU10009 Mainshaft Shim Kit
QU10009B Basic Mainshaft Shim Kit
QK1010 Complete Small Parts Kit
QU10221 Basic Small Parts Kit
QU10154 38 Tooth Countershaft Drive Gear for 1994-1995 with Modular Countershaft
QU10078 One Piece Countershaft Assembly for 1995-1996 5.61 Reverse Gear Ratio
QU90020 NV4500 Manual Transmission Oil
TM1003 NV4500 Shop Manual
V1003DVD NV4500 Overhaul Video

Tech Note 7: Synchronizer Parts
Matching NV4500 Synchronizer Parts for QU10054 Input Gear are: 

4th Gear Clutch Synchronizer
Assembly
Synchronizer
Hub
Synchronizer
Slider
Strut
Kit
Synchronizer
Ring
QU10049 or QU10702  QU10732 QU10020
or
QU10122
QU10021 QK1099 QU10004

 

Applications
Dodge:
D150, W150, D250, W250, D350, W350 with Gasline Engines and NV4500 5 Speed Transmission: 1992, 1993
Dodge Ramcharger and Plymouth Trailduster with NV4500 5 Speed Transmission: 1992, 1993

Warranty

Tools, New Parts, and Torque King® products in a kit or sold individually are warranted to the original purchaser to be free from defects in materials and workmanship for a period of one year from the date of sale. Certain Products, such as Warn® Hubs may be covered by additional manufacturer's warranties. THERE ARE NO OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THE EXCLUSIVE REMEDIES FOR A WARRANTY CLAIM HEREUNDER IS RETURN OF THE GOODS TO TORQUE KING 4X4 FOR REPAIR, REPLACEMENT, OR REPAYMENT OF THE PURCHASE PRICE. ALL CLAIMS FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES ARE HEREBY EXCLUDED FROM THIS LIMITED WARRANTY.

Product Reviews

No reviews yet Write a Review

Delivery & Returns

Shipping times are estimated in your cart.

 

More info can be found at the link below.