- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
QU10069 NV4500HD Mainshaft 5th Gear Nut Set - 1994-2004 Dodge Ram
10069$47.98QU10069 Dodge NV4500HD Large Set Screw Type Mainshaft Nut Set is an aftermarket part for all Dodge 29 spline 4x4 and Dodge 31 spline 4x2 New Venture NV4500HD 5 speed manual transmissions. Kit includes Nut, Concave Washer, 2 Brass Thread Protectors, and 2... -
QU50078 NP231, NP241 Transfer Case Aluminum Range Shift Fork
50078$47.98QU50078 New Process NP231, NP241 Transfer Case Aluminum Range Shift Fork Aluminum Range Fork with molded shift fork pads is a genuine New Process part that fits many New Process/New Venture NP231, NP241 chain drive transfer cases in mid 1990's and newer... -
QK4625 Right Side Axle Bushing & Bearing Kit 1994-1999 Ram 2500, 3500
4625$21.98QK4625 Right Side Axle Bushing and Bearing Set includes QU40292 needle bearing that supports the Differential Output Shaft (what Dodge calls the Intermediate Shaft) and QU40107 plastic bushing pressed in the end of the right axle shaft on 1994-1999 Heavy... -
QU11013 Rear Extension Housing NV271D, NV273D
11013$199.98QU11013 New Process NV271D, NV273D Transfer Case Rear Extension Housing for Dodge Ram is a genuine New Process/New Venture original equipment Rear Extension Housing for your 2003 or newer Dodge Ram 2500 or Ram 3500 4x4 truck with a New Process Gear (NPG)... -
QU40051 2" Tabbed Spindle Nut Lock Washer for Dana 60, Dana 70 Axles
40051$6.98QU40051 Bend Over Tab 2" ID Spindle Lock Washer with Wide Key Tab fits 2" diameter spindles that use hex nuts measuring either 2-1/2" (QU40052) or 2-9/16" (QU11070) across the flats. This genuine original equipment, non reusable, Dana Spicer washer was... -
QU40084 Large Driveshaft or Ford IFS Axle Shaft Boot Clamp
40084$3.98QU40084 Large Driveshaft or Ford IFS Axle Shaft Boot Clamp is a one-ear, crimp type stainless steel clamp that is mainly used on mid 1980s and newer driveshafts to seal the large end of 4 or 5 Pleat Driveshaft Boot to the female spline Slip Yoke. QU40084... -
QU10104 Transmission Breather and Vent Assembly for NPG, NVG
10104$14.98QU10104 Breather Vent and Hose Assembly for New Process and New Venture is a New Old Stock (NOS) genuine New Venture Gear Replacement Vent assembly with a short hose that is specific to NV4500 5 speed manual transmissions, but it also fits NV5600 6... -
QU40414 Outer Axle Shaft Snap Ring for Ford Super Duty Front Axles
40414$7.98QU40414 2005-2019 Ford F250, F350, F450, F550 Super Duty® Outer Axle Shaft Snap Ring is a genuine Dana Spicer original equipment part that fits in a groove machined in the Outer Axle Shaft to hold the Outer Shaft in position in the Ford Dana Super... -
QT1503 Rear Wheel Seal Installer for Ford and Dodge Dana 70/80
1503$41.56QT1503 Dana 70 and Dana 80 Rear Wheel Seal Installer for Ford and Dodge is specifically made to install QU40449 and similar flanged inner wheel seals in 1970's to current Ford F-350 trucks and 1994 to 2002 Dodge 3/4 ton Ram 2500 and 1 ton Ram 3500... -
QU40118 2-9/16" Rounded Hex Rear Spindle Nut with 2" Thread for Dodge & Ford Dana 60, 70, 80 Axles
40118$30.98QU40118 2-9/16 Rounded Hex Locking Rear Spindle Nut for Dodge, Ram, and Ford Dana 60, 70, and 80 Rear Axles is a Case hardened, USA Made, SINGLE USE, OEM Spec Replacement Spindle Nut with 2" Right Hand Thread for all 1979 to 2002 Dodge 3/4 ton and 1 ton... -
QU10060 Cast Iron NV4500 4x4 Transmission Tail Housing for Dodge
10060$209.98QU10060 Cast Iron 1994-2005 Dodge NV4500 4x4 Rear Housing QU10060 is a new production, accurately machined, Cast Iron replacement 4x4 Tailshaft housing for all 1994-2005 Dodge NV4500LD and 1994-2004 NV4500HD 4x4 transmissions. Recommended for... -
QK1099 6 Piece NV4500 Synchro Strut & Spring Kit fits 3/4, 5th, & Reverse
1099$9.98QK1099 NV4500 3-4, 5th, and Reverse Gear Synchro Strut Kit has the 3 QU10309 coil springs and 3 QU10308 steel struts used with each 3-4, 5th, and reverse synchronizer assembly. Included in QK1010 Small Parts Kit. Use one Kit per Synchronizer Assembly...