- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
QU50162 3/8" Deep Cup Plug for NP200, NP201, early NP205
50162$0.98QU50162 3/8" Deep Cup NP205 Case Access Soft Plug for the shift fork pin and interlock holes in early production NP205 cases. QU50162 Steel Plug is a USA made deep cup soft plug that is an essential part when rebuilding New Process NP200, NP201,... -
QU50224 Large NP205 Transfer Case Access Hole Plug Approx 7/16" OD
50224$2.98QU50224 Large Deep Cup NP205 Case Access Hole Soft Plug for the shift fork pin and interlock holes in late 1970's to 1993 New Process NP205 cases. Diameter is approximately 0.447". Sold individually, but Requires 4 per case. (Included in application... -
TKA2053 9 Piece Idler Gear and Output Shaft Shim Kit
2053$39.98TKA2053 9 Piece Idler Gear and Output Shaft Shim Kit contains an assortment of shims from 0.004" to 0.040" for precise adjustment of your New Process NP205, NP200, or NP201 gear drive Transfer Case Idler Gear end-play. Also used on NP200 and NP201 rear... -
QK2036 7/8" Thread Nut & Washer Kit for NPG Transfer Case Shafts
2036$17.98QK2036 New Process Transfer Case Shaft Nut and Washer Set replaces worn or damaged New Process Gear (NPG) NP203 and NP205 32 spline output/remote input or idler shaft hardware. Kit includes Hardened Washer and Special USA made Tri-Lobe original equipment... -
QU10104 Transmission Breather and Vent Assembly for NPG, NVG
10104$14.98QU10104 Breather Vent and Hose Assembly for New Process and New Venture is a New Old Stock (NOS) genuine New Venture Gear Replacement Vent assembly with a short hose that is specific to NV4500 5 speed manual transmissions, but it also fits NV5600 6... -
QU30040 Vent Fitting for 5/16" Hose
30040$5.98QU30040 Vent Fitting for 5/16" Hose fits most axle, transmission, and transfer cases with 5/16" vent hoses. Also see QU10104 Vent and Hose Assembly Need More Info? Use the handy Links below to access over 40 years of Dan's product and... -
QU10504 Shaft Nut for NP200, NP201, NP202, NP203 NP205 Transfer Cases
10504$15.98QU10504 NP200, NP201, NP202, NP203, NP205 Transfer Case Shaft Lock Nut is a USA Made, 7/8" Extra Fine Thread, Low-Profile, OE Spec Hex Lock Nut for Threaded Output, Counter Shaft, or Remote Input shafts on New Process NP200, NP201, NP202, NP203,... -
QU10316 Shaft Anti-Rotation Pin NP205 NV4500
10316$3.21QU10316 New Process NP205 Transfer Case Low Gear and NV4500 Transmission Shaft Anti-Rotation Pins. One of these tiny, genuine NPG, Hardened Steel Pins is used in each output shaft to prevent your QU50256 Low Gear Thrust Washers from rotating on your... -
QU50191 Chip Magnet for NPG, NVG Transfer Cases and Transmissions
50191$6.98QU50191 Chip Magnet for New Process, New Venture Transfer Cases and Transmissions is a genuine original equipment Chip Magnet that fits a host of Transmission and Transfer Cases manufactured by Muncie, New Process Gear, New Venture Gear, and Magna... -
QU10696AM Tanged Inner (thin steel) Low Gear Thrust Washer NP205
9910696$9.98QU10696AM Tanged Inner (thin steel) Low Gear Thrust Washer for New Process NP205 Transfer Cases Two of these Tanged Steel Washers are used on the rear output shaft of every Chevy, Dodge, Ford, GMC, and IHC NP205 Transfer Case. Imported. Sold... -
QU10988 0.010" Idler Shaft Shim for NP200, NP201, NP205
10988$9.98QU10988 0.010" Thickness Idler Gear or Rear Shaft Shim for New Process NP205, NP200, and NP201. Individual shim may vary up to 15% from the normal thickness. Precision stamped and de-burred shims have the correct ID/OD to clear the idler shaft and... -
QU50350 NP205 Transfer Case Pilot Bearing Thrust Washer
50350$1.98QU50350 NP205 Transfer Case Pilot Bearing Thrust Washer is installed in the front of the rear input shaft between the 15 pilot rollers and the snap ring. Need More Info? Use the handy Links below to access over 40 years of Dan's product and vehicle...